Our products

Designed for automotive body repair painting:
Used as the first layer in two-layer coating systems (base + clearcoat).
Applied on pre-primed and filled surfaces.
After applying this layer, it is recommended to cover it with 2+1 MS or HS clearcoat.
Products: Metallic Basecoat
Substrates:
Sanded factory coating
For lacquer coatings with up to 1 year of service, "Anti-silicone" can be used instead of sanding. Primed and filled surfaces
Surface Preparation:
Degrease the metal surface with white spirit.
Repair the surface using polyester filler and perform dry sanding with P280-P320.
Prime the surface with an anticorrosion primer.
Apply leveling primers and sand the surface.
Pot life: 1.5 hours at 20°C
Thinning:
Metallic thinner, up to 30% of the enamel mass.
Application Viscosity:
15-17 seconds at 20°C using B3-4 (DIN Cup 4).
Coating Thickness: 15-20 microns / 2 layers
Number of Layers: 1.5-2
Equipment Cleaning: Solvent 646/647
Shelf Life: 24 months.

Designed for automotive repair painting.

Products:
Enamel AK-1301
Universal acrylic hardener (1301)
Acrylic universal thinner (1301) / slow thinner (1301-M), or their mixture
Substrates:
Sanded factory coating (for enamel coatings with up to 1 year of service life, instead of sanding, "Anti-silicone" can be used)
Primed or filled surfaces
Surface Preparation:
Degrease the metal surface with white spirit.
Repair the surface using polyester filler and perform dry sanding with P280-P320.
Prime the surface with phosphating primer WASH PRIMER VL-02.
Apply leveling primers FILLER 6+1, FILLER 3+1, or FILLER HS.
Perform dry sanding with P320-P400 or wet sanding with P800-P1000.
Application Conditions:
Optimal temperature: +20°C
Minimum temperature: +15°C
Relative humidity: no more than 75%
Mixing:
Enamel: hardener: thinner = 4:1:1.5 (by weight)
Enamel: hardener: thinner = 4:1:1.6 (by volume)
Pot life: 8 hours at +20°C
Drying:
At (20 ± 2)°C — 16 hours
At (60 ± 2)°C — 45 minutes
At (80 ± 2)°C — 30 minutes
Shelf Life: 24 months.

A two-component system designed for automotive body repair painting.
Products:
Enamel AK-1305
Hardener 1305
Vikron acrylic thinner
Substrates:
Sanded factory coating
Primed or filled surfaces
Surface Preparation:
Degrease the metal surface with white spirit.
Repair the surface using polyester filler and perform dry sanding with P240-P320.
Prime the surface that has been sanded down to the metal using WASH PRIMER VL-02 anticorrosion primer.
Apply 2K acrylic primer (3+1, 4+1, or 5+1), followed by dry sanding with P320-P400 or wet sanding with P800-P1000.
Application Conditions:
Optimal temperature: +20°C
Minimum temperature: +15°C
Relative humidity: no more than 75%
Mixing: Enamel: hardener = 2:1
Pot life: 4 hours at +20°C
Thinning: Vikron thinner — 10-20%
Application Viscosity: 18-20 seconds at +20°C using B3-4 (DIN Cup 4).
Application Equipment:
Compliant spray gun:
Nozzle size: 1.4 - 1.6 mm
Working pressure: 2.0 - 4.0 atm
HVLP spray gun:
Nozzle size: 1.3 - 1.7 mm
Working pressure: 2 atm
Drying:
At 20°C — 16 hours
At 60°C — 45 minutes
Flash-off Time: 10 minutes.
Packaging: 0.8 L
Shelf Life: 24 months.

Single-component acrylic primer is designed to insulate and level the repaired areas with a thin layer. Provides a reliable coating and is characterized by a short drying time.

A single-component primer designed for plastic parts, intended for the initial priming of plastic surfaces and enhancing adhesion of paint coatings. Suitable for use on plastic components, including polypropylene, without the need for flame treatment.

Color: Transparent, metallic
Substrates:
Most plastics used in the automotive industry.
Note: Vikron 1K cannot be applied to certain types of plastics (e.g., PE).
Not suitable for plastics sensitive to organic solvents, such as polystyrene (PS).
Surface Preparation:
Use a plastic cleaner to clean the surface.
Use tack cloths to remove dust.
Application Equipment:
Compliant spray gun:
Nozzle size: 1.4 - 1.6 mm
Working pressure: 2.8 - 3.1 atm
HVLP spray gun:
Nozzle size: 1.3 - 1.7 mm
Working pressure: 2.0 atm
Mixing: Ready to use.
Number of Layers: 1 full layer.
Flash-off Time: 10 minutes at 20°C.
Drying: 10 minutes at 20°C.
Next Coating: Basecoats and acrylic enamels can be applied over the Vikron 1K plastic primer.
Shelf Life: 24 months.

Developed for Use in the Automotive Glass Replacement Segment It provides excellent adhesion to major structural materials such as glass, painted metals, aluminum, plastics, wood, and more.

Designed for Seam Sealing and Bonding

It is intended for seam sealing, bonding non-load-bearing elements, as well as reducing vibration and improving sound insulation properties during vehicle repair and manufacturing.

It is designed to dilute 2K acrylic primers, enamels, and lacquers to working viscosity.

Designed for thinning metallic enamels. Add directly before using the enamel.
Composition: A mixture of organic liquids.
Shelf Life: 24 months.

The thinner is slow, universal. It is intended for diluting basic enamels, as well as acrylic products. The specifics of this thinner are that it works excellently at high coloring temperatures in very hot conditions. Slow, when thinned, the paint density does not decrease, the base enamels are not dry, the surface looks perfect.

Chrome remover for plastic effectively removes the top chrome layer in a short time without damaging the plastic surface. After application, simply rinse with water and lightly scuff the surface with a Scotch-Brite pad.

Painting can be carried out using the following system:
— plastic primer,
— basecoat,
— clear coat,

or 2K acrylic enamels. This ensures durability, high quality, and a flawless finish.

To be used according to the instructions provided with the manufacturer's paint and coating materials.
Soluble Materials:

• Paints
• Varnishes
• Enamels
• Adhesives
• Mastics
• Fillers
• Primers

It is intended for diluting paint and varnish materials based on polyvinyl chloride, chlorinated resins (PCH-LS), polyacrylic resins, and other film-forming components. It is added in small portions while mixing the material until the desired consistency is achieved.

Designed for thinning varnishes, paints, enamels, and mastics. To be used according to the instructions provided with the manufacturer's paint and coating materials.
Soluble Materials:

• Paints
• Varnishes
• Enamels
• Adhesives
• Mastics for rubber and leather products.

Also used for degreasing surfaces and refueling blowtorches.

A means for effective removal of oils, fats, silicones, and other contaminants from the surface before painting, primering, grinding, or gluing. Ensures cleanliness and improves the adhesion of subsequent coating layers.

A universal spray gun designed for applying 1K synthetic enamels, primers, liquid putties, and other paint and varnish materials.

A professional top tank paint gun is designed for applying acrylic enamels, varnishes, and high-viscosity materials. Perfect for both professionals and enthusiasts. LVMP spraying system.

Professional HVLP spray paint gun for car painting. It has excellent atomization, is convenient for applying basic enamels and acrylic lacquers, and is economical in terms of paint consumption.

A universal professional, reliable paint gun is excellent for applying various LCDs in any conditions without losing quality and with minimal material consumption.

A two-component acrylic clearcoat.
Products:
2K acrylic clearcoat 2+1 MS
Hardener for 2+1 MS clearcoat
Vikron acrylic thinner
Substrates:
Sanded factory coating
Primed and filled surfaces
Surface Preparation:
Degrease the metal surface with white spirit.
Repair the surface using polyester filler and perform dry sanding with P240-P320.
Prime the surface sanded down to metal with WASH PRIMER VL-02 anticorrosion primer.
Apply 2K acrylic primer (3+1, 4+1, or 5+1), then dry sand with P320-P400 or wet sand with P800-P1000.
Apply metallic base coat.
Application Conditions:
Optimal temperature: +20°C
Minimum temperature: +15°C
Relative humidity: no more than 75%
Mixing:
Clearcoat: hardener = 2:1
Pot Life: 1.5 hours at 20°C
Application Equipment:
Compliant spray gun:
Nozzle size: 1.4 - 1.6 mm
Working pressure: 2.0 atm
HVLP spray gun:
Nozzle size: 1.3 - 1.7 mm
Working pressure: 2.0 atm
Flash-off time: 10 minutes
Coating Thickness: 35-45 microns / 2 layers
Number of Layers: 2.5-3
Drying:
At 20°C — 12 hours
At 60°C — 60 minutes
At 80°C — 30 minutes
Equipment Cleaning:
Metallic thinner
Solvent 646/647
Shelf Life: 24 months.

A two-component acrylic clearcoat.

Products:
2K acrylic clearcoat 2+1 MS
Hardener for 2+1 MS clearcoat
Vikron acrylic thinner
Substrates:
Sanded factory coating
Metallic or non-metallic base coat
Surface Preparation:
Degrease the metal surface with white spirit.
Repair the surface using polyester filler and perform dry sanding with P240-P320.
Prime the surface that has been sanded down to the metal using WASH PRIMER VL-02 anticorrosion primer.
Apply 2K acrylic primer (3+1, 4+1, or 5+1), followed by dry sanding with P320-P400 or wet sanding with P800-P1000.
Apply the metallic base coat.
Application Conditions:
Optimal temperature: +20°C
Minimum temperature: +15°C
Relative humidity: no more than 75%
Mixing: Clearcoat: hardener = 2:1
Pot life: 1.5 hours at 20°C.
Application Equipment:
Compliant spray gun:
Nozzle size: 1.4 - 1.6 mm
Working pressure: 3.0 - 4.0 atm
HVLP spray gun:
Nozzle size: 1.3 - 1.7 mm
Working pressure: 2.0 atm
Flash-off Time: 10 minutes.
Coating Thickness: 35-45 microns / 2 layers
Number of Layers: 2.5-3
Drying:
At 20°C — 12 hours
At 60°C — 60 minutes
At 80°C — 30 minutes
Equipment Cleaning:
Metallic thinner
Solvent 646/647
Shelf Life: 24 months.

Two-component acrylic enamel is intended for repairing the body and body parts of light vehicles, as well as for painting other vehicles. The enamel provides high decorative and protective properties of the coating.